Difference between revisions of "Teak Tables"

From c34.org
Jump to navigation Jump to search
Line 1: Line 1:
 +
==A few approaches to smaller, more manageable saloon tables==
 +
 +
===Quiet Island===
 +
[[image:Dinette1.jpg|border|350px|right]][[image:Dinette2.jpg|border|350px|right]]
 +
'''By Bob & Cheryl Kuba, ''Quiet Island'' #1291 (1994)'''
 +
 +
Here's a more practical Dinette table. If we plan to have more guests than the v-berth and aft stateroom can handle, the original table can be re-installed for the additional sleeping space. It sure makes it easier to access the storage areas!
 +
 +
I re-cycled an old kitchen table top by shaping it to the size that looked proportional by cutting it with a jigsaw. Then, after roughing up the original Formica top with sandpaper, I used a brush-on contact cement, and glued a piece of 1/8" birch plywood to the top. I left a small overhang around the edges so I could sand it down to the same size as the table base below it. Contact cement is very unforgiving, and if you don't position your project exactly right on the first try, it's impossible to remove. So I left myself a margin for error, and then just sanded it down.
 +
 +
I experimented on a scrap piece of the birch plywood, and after mixing a blend of oak and red mahogany wood stains, I stained it to match the interior wood shade. It took 3-tries to get something I was happy with.
 +
 +
To give it a finished look, I bought some rounded teak corners and straight teak edge molding and attached it to the edges using a waterproof wood glue, Titebond II. The hard part was getting all the pieces to fit flush up against each other, but that's just a matter of fitting, sanding, fitting, and then sanding again to get that perfect fit.
 +
 +
Then it was five coats of marine spar varnish.
 +
 +
After a season of cruising its held up well. Although, this winter I think I am going to pour a layer of self-leveling clear resin over the surface to better protect it. It's a product called EnviroTex Lite, and can be found at most paint stores, or at www.eti-usa.com
 +
 +
 +
----
 +
===Juliana's trimmed table===
 +
'''By Bryan Pfaffenberger, ''Juliana'', #680'''
 +
 +
 
Older C34s are equipped with a Formica-covered table. Designed to lower in order to transform the settee into a double berth, the table is too large to allow sitters to enter the settee comfortably.  
 
Older C34s are equipped with a Formica-covered table. Designed to lower in order to transform the settee into a double berth, the table is too large to allow sitters to enter the settee comfortably.  
  
Line 5: Line 29:
 
Constructed by a master woodworker in Hampton, Virginia, the table is solid 5/8" teak and adds greatly to the boat's interior beauty.  
 
Constructed by a master woodworker in Hampton, Virginia, the table is solid 5/8" teak and adds greatly to the boat's interior beauty.  
  
'''Bryan Pfaffenberger, ''Juliana'', #680'''
 
  
 
----
 
----
 +
===Kindred Spirit's "cocktail table"===
 +
'''By Al and Michele Watson ''Kindred Spirit'' #55'''
  
'''Main Cabin Dinette Table Storage & Replacement with Smaller Coffee Type Table'''
 
  
 
We rafted with another C34 at Block Island and my son mentioned the next day that our boat looked smaller. I assured him we all had the same boat. Well I started thinking (very dangerous when I do that) the only boat difference was he stored his main table aft and had an octagon coffee table in its place.  
 
We rafted with another C34 at Block Island and my son mentioned the next day that our boat looked smaller. I assured him we all had the same boat. Well I started thinking (very dangerous when I do that) the only boat difference was he stored his main table aft and had an octagon coffee table in its place.  
Line 23: Line 47:
 
Possibly, two small type clamps attached to the large table bottom side. I would like to put fiddles at four points around the table but it would hinder the larger table being put back on top for the four person dinner setting. Now the question is how long can I get away with the temporary pine table??? I did put white formica on the top!  
 
Possibly, two small type clamps attached to the large table bottom side. I would like to put fiddles at four points around the table but it would hinder the larger table being put back on top for the four person dinner setting. Now the question is how long can I get away with the temporary pine table??? I did put white formica on the top!  
  
'''Al and Michele Watson ''Kindred Spirit'' #55'''
+
<gallery caption="Click any image to enlarge" widths="200px" heights="210px" perrow=3>
 +
Image:watson-table1.jpg
 +
Image:watson-table2.jpg
 +
Image:watson-table3.jpg
 +
</gallery>
  
[[Image:watson-table1.jpg|300px]] [[Image:watson-table2.jpg|300px]] [[Image:watson-table3.jpg|300px]]
 
  
 
----
 
----
 +
===Espresso's Thai Teak table===
 +
'''By Craig Illman, ''Espresso'', #1150'''
 +
  
 
I purchased a smaller salon table (21" x31") from www.thaiteakmarine.com. After waiting almost two months for delivery, I finished with eight coats of Top Secret (www.topsecretcoatings.com) one part clear epoxy. I didn't want to remove the spider from the original table in case I wanted to bring it temporarily back aboard, so I picked up another 1-3/4" spider from Cabelas. The smaller table still handles four diners and makes it much easier to access the starboard storage areas.
 
I purchased a smaller salon table (21" x31") from www.thaiteakmarine.com. After waiting almost two months for delivery, I finished with eight coats of Top Secret (www.topsecretcoatings.com) one part clear epoxy. I didn't want to remove the spider from the original table in case I wanted to bring it temporarily back aboard, so I picked up another 1-3/4" spider from Cabelas. The smaller table still handles four diners and makes it much easier to access the starboard storage areas.
  
''' Craig Illman, ''Espresso'', #1150'''
+
[[Image:teak-table1.jpg|border|350px]] [[Image:teak-table2.jpg|border|350px]]
 
 
[[Image:teak-table1.jpg|350px]] [[Image:teak-table2.jpg|350px]]
 

Revision as of 18:19, 31 January 2009

A few approaches to smaller, more manageable saloon tables

Quiet Island

Dinette1.jpg
Dinette2.jpg

By Bob & Cheryl Kuba, Quiet Island #1291 (1994)

Here's a more practical Dinette table. If we plan to have more guests than the v-berth and aft stateroom can handle, the original table can be re-installed for the additional sleeping space. It sure makes it easier to access the storage areas!

I re-cycled an old kitchen table top by shaping it to the size that looked proportional by cutting it with a jigsaw. Then, after roughing up the original Formica top with sandpaper, I used a brush-on contact cement, and glued a piece of 1/8" birch plywood to the top. I left a small overhang around the edges so I could sand it down to the same size as the table base below it. Contact cement is very unforgiving, and if you don't position your project exactly right on the first try, it's impossible to remove. So I left myself a margin for error, and then just sanded it down.

I experimented on a scrap piece of the birch plywood, and after mixing a blend of oak and red mahogany wood stains, I stained it to match the interior wood shade. It took 3-tries to get something I was happy with.

To give it a finished look, I bought some rounded teak corners and straight teak edge molding and attached it to the edges using a waterproof wood glue, Titebond II. The hard part was getting all the pieces to fit flush up against each other, but that's just a matter of fitting, sanding, fitting, and then sanding again to get that perfect fit.

Then it was five coats of marine spar varnish.

After a season of cruising its held up well. Although, this winter I think I am going to pour a layer of self-leveling clear resin over the surface to better protect it. It's a product called EnviroTex Lite, and can be found at most paint stores, or at www.eti-usa.com



Juliana's trimmed table

By Bryan Pfaffenberger, Juliana, #680


Older C34s are equipped with a Formica-covered table. Designed to lower in order to transform the settee into a double berth, the table is too large to allow sitters to enter the settee comfortably.

Our new teak table is four inches smaller on three sides (the sides facing the settee), allowing easier ingress and egress.

Constructed by a master woodworker in Hampton, Virginia, the table is solid 5/8" teak and adds greatly to the boat's interior beauty.



Kindred Spirit's "cocktail table"

By Al and Michele Watson Kindred Spirit #55


We rafted with another C34 at Block Island and my son mentioned the next day that our boat looked smaller. I assured him we all had the same boat. Well I started thinking (very dangerous when I do that) the only boat difference was he stored his main table aft and had an octagon coffee table in its place.

This made it easier to get to all the storage behind the table. We had also seen another C34 with their table cut and hinged on one side for more room. Both nice ideas along with all those in the MainSheet but I hated to cut the table and the octagon shape was not our style so I continued thinking.

When we got home I took a scrape piece 16 x 25 inch of 1 1/2 inch laminated pine board (doesn't everyone have this in their garage! I do) Now the trick, not round, not 5-6 or 8 sided, hey!!! The top of the house toilet looks about right! Apart came the toilet cover (Michele didn't know that part) and I traced the shape on both ends of the board (went 3/4 inch larger all around to fill the board). I cut the shape out (returned the seat to the toilet).

When we returned to the boat and I removed the large table, stood it on end and put it good side to the wall just inside the aft cabin. Well who wants that ugly underside bracket and plywood showing in the aft.

The idea light bulb lit again. I took the bracket off.....follow me here....turned the table good side out and ran a bungy cord around it to hold it in rough seas. Looks so nice, Michele went into the aft looking for it and did not notice it, the bungy is now another towel rack. OK, now I took the bracket and mounted it to my oval table....put it back on the post,....got funny and added two full place settings and called Michele down for the big test. Boat Looks Bigger!. Much easier to get around to all the hidden storage. The only thing that I now have to do is figure a way to lay the larger table over the smaller and hold it in place.

Possibly, two small type clamps attached to the large table bottom side. I would like to put fiddles at four points around the table but it would hinder the larger table being put back on top for the four person dinner setting. Now the question is how long can I get away with the temporary pine table??? I did put white formica on the top!



Espresso's Thai Teak table

By Craig Illman, Espresso, #1150


I purchased a smaller salon table (21" x31") from www.thaiteakmarine.com. After waiting almost two months for delivery, I finished with eight coats of Top Secret (www.topsecretcoatings.com) one part clear epoxy. I didn't want to remove the spider from the original table in case I wanted to bring it temporarily back aboard, so I picked up another 1-3/4" spider from Cabelas. The smaller table still handles four diners and makes it much easier to access the starboard storage areas.

Teak-table1.jpg Teak-table2.jpg