Difference between revisions of "Sink Access"

From c34.org
Jump to navigation Jump to search
Line 26: Line 26:
  
 
When I got home, like a 1st grader showing his mom his brand new finger oainting masterpiece, I showed the admiral the photos. She liked the access and the piece of mind it gave knowing we could easily get to any leak that might develop behind the sink. However she didn't like the way it looked. She grudgingly agreed to my plan because it was hidden behind the cushion.
 
When I got home, like a 1st grader showing his mom his brand new finger oainting masterpiece, I showed the admiral the photos. She liked the access and the piece of mind it gave knowing we could easily get to any leak that might develop behind the sink. However she didn't like the way it looked. She grudgingly agreed to my plan because it was hidden behind the cushion.
 +
 +
The next day I proudly posted my pictures on the C-34 forum. To my surprise, many of the great members agreed with my wife. They suggested I cover it with a hatch. Whent these folks AND the admiral agree, my logic might be a bit off. So, I orderd a Sure Seal Hatch (T-H MARINE HAT-1324-2-DP) from West Marine. The access area will have to be enlarged to accept the hatch as it is a bit bigger than the cut out.
 +
 +
(More when the hatch gets here)

Revision as of 12:37, 20 January 2009

How to gain access to the back of your galley sink

By Lance Jones, Kitty's Cat #622 (1988)

Area before the project began
Cut-out area marked
Cut-out...cut-out
View inside through the cut-out
Different angle
Wide view
Cushion in place

BEGIN ADDING PROJECT TEXT HERE.... I recently had Kitty's Cat surveyed. During the survey, I followed the surveyor around and when he had difficulty getting to the faucet to check a fitting, it gave me an idea. I also wanted to do some of the great sink upgrades on the C-34 Association's project page; but, had trouble getting to the sink bottom from the two access points through the drawer and hot water heater door. So, after checking with the admiral, I set off to add an access point behind the galley sink.

The tools I used for this project were a Dremel tool with cutting bit and cutting guide. I also used a Dremel sanding stone and sanding block with 80 grit paper.

I measured out an area 7 x 18 inches that was centered on the back of the sink and located roughly at what I thought was the bottom of the sink. My next step was to mark out the area.

The cutting begins!

I used a cutting bit with a cutting guide on the Dremel. The guide would allow me to vary the depth of the cut without worrying about cutting a hose hidden behind the seat. I had to make two cut laps as I didn't cut deep enough the first time around -- better safe than sorry.

After the panel was out, I was AMAZED at how much access this gave me. I could reach everything I need to reach -- the drains, hot water heater, faucet hoses and more.

My next step was to remove the rough edges on the cut. I switched to a sanding stone for the Dremel. After a few passes with the stone, I followed up with a sanding block and 80 grit paper. At this point, I was planning on leaving the access panel open and line the edges with edge guard similar to the cubby areas behind the port and starboard settees. I was at a good stopping point for now.

When I got home, like a 1st grader showing his mom his brand new finger oainting masterpiece, I showed the admiral the photos. She liked the access and the piece of mind it gave knowing we could easily get to any leak that might develop behind the sink. However she didn't like the way it looked. She grudgingly agreed to my plan because it was hidden behind the cushion.

The next day I proudly posted my pictures on the C-34 forum. To my surprise, many of the great members agreed with my wife. They suggested I cover it with a hatch. Whent these folks AND the admiral agree, my logic might be a bit off. So, I orderd a Sure Seal Hatch (T-H MARINE HAT-1324-2-DP) from West Marine. The access area will have to be enlarged to accept the hatch as it is a bit bigger than the cut out.

(More when the hatch gets here)